MMC Roll Form

Calculating Per-Piece Costs in Roll Forming

Ryan Hernden

You’ll often hear roll forming described as being a cost-effective process. You may also hear that it’s a high-volume process. Both descriptions are true, although also a little too vague to be useful. If you really want to calculate per-piece costs in roll forming, you’ll need an understanding of the process and the cost drivers. […]

a worker inspects a metal roll form part on a factory floor

You’ll often hear roll forming described as being a cost-effective process. You may also hear that it’s a high-volume process. Both descriptions are true, although also a little too vague to be useful. If you really want to calculate per-piece costs in roll forming, you’ll need an understanding of the process and the cost drivers.

Roll forming is a process for forming strips of metal sheet into shapes with a uniform profile along their length. It entails feeding a metal coil into a line of roll stands. Each stand has pairs of rollers that deform the metal. Over multiple stands, this can create complex shapes like drawer slides or seat tracks.

Many lines start with a pre-punch operation that adds holes, notches, and louvers. They also typically end with a cutting stage that crops formed profiles to length. Roll forming lines can hold tight tolerances and run at high speeds.

Roll forming costs have two main elements: raw material and line running costs. Inevitably, overheads, shipping, and other elements creep in, but these are the main drivers. Line costs include setup time, which can be lengthy, but the impact on piece costs is reduced by forming large quantities in long production runs.

For a closer look at roll forming piece costs, keep reading.

Raw Material

Roll forming is very efficient in terms of how material is utilized. However, despite the low level of waste, material costs make up between 40 and 80% of the final piece cost.

When assessing the cost impact of material, the two factors to consider are the type of metal specified and the amount required per piece. Piece weight can be calculated from the physical dimensions and material density. From here, it’s possible to determine a material cost per piece.

Carbon and galvanized steel are usually the least expensive materials. Aluminum and stainless steel are more expensive, although the precise cost depends on the series or grade selected. Copper and brass are the most costly roll forming materials.

When looking at the quantity and weight of material used, while it’s obvious that a larger piece uses more, an underappreciated aspect is the impact of thickness. With heavier gauge material, the weight and cost of each piece go up, but there’s also an impact on production speed and productivity.

When forming heavier gauge material, the line runs slower as more force is needed to produce the required shape. In addition, the feeding coil will hold a shorter length of material, so coil changes will be more frequent. Plus, finished product handling can be slower and more expensive.

Costs are reduced by using the thinnest gauge of material that will produce profiles of acceptable quality. Adding ribs, flanges, and reinforcing channels will increase stiffness and perhaps allow the use of thinner material. However, if the material becomes too thin, it may wrinkle and deform.

# of Pieces Produced

Depending on material type and thickness, a roll forming line can run at between 100 and 300 feet per minute. However, even with the best possible organization and order scheduling, it can take a long time – possibly even several hours – to change over from one product to another.

As a result, small orders can be expensive because the total number of machine hours is still relatively large. But as order size goes up, changeover time becomes a smaller proportion of the total time the line is in use. This reduces the cost of manufacturing each piece. On large orders, meaning those for more than 10,000 linear feet, the per-piece cost of setup becomes very small.

Type of Profile Required/Tooling Design

Roll forming rolls are designed and machined to tight tolerances in order to produce a specific deformation. The rolls are produced from alloy steel and often undergo heat treatment, which all serves to make them relatively expensive. Plus, they can wear, especially when forming tight radii features, and need periodic re-machining or even replacement.

When a design needs new custom rolls making, the cost of these should be included in the piece cost. However, to help customers avoid this expense, MMC maintains an in-house tooling inventory. Accordingly, to drive down roll forming piece costs, try to design profiles that use this existing library rather than needing new tools.

Why Roll Forming Works Better for High-Volume Production

Roll forming is a continuous process where material should keep flowing through the roll stations. Stoppages and other interruptions tend to cause a lot of material waste and rolling line downtime.

In addition, as noted previously, long changeover times make short production runs very costly in terms of piece costs.

As a result, any analysis of roll forming piece costs with volume will show that unit costs fall rapidly as order size rises. The cost advantages of the process are greatest when volumes exceed 10,000 linear feet of material. For smaller quantities, press brake forming can be a competitive alternative.

Get a Free Estimate & Project Analysis

While roll forming is an efficient and potentially very cost-effective process for making uniform cross-section metal shapes, every project is different. The guidance given here provides a way of estimating and also reducing costs, but the only way to determine actual per-piece costs in roll forming is through a detailed project analysis.

As a U.S.-based custom roll forming company specializing in long lengths and critical finishes, we can undertake this kind of study for current or prospective customers requiring accurate per-piece cost estimates.

Our Michigan facility is equipped with 14 roll mills, capable of performing up to 21 passes. We can produce constant sweep profiles, and with roll shaft diameters of up to 3.0”, we can form materials like High Strength Low Alloy (HSLA) steel. We do only take on high-volume projects using 10,000 linear feet or more of material.

Use our Request a Quote form to get started.

© 2026
MMC Products Company. All Rights Reserved.